- 550 - pin 1 pin 3 positive ct pin 2 case GP1001 thru gp1007 10.0 amps. glass passivated rectifiers voltage range 50 to 1000 volts current 10.0 amperes f eatures low forward voltage drop high current capability high reliability high surge current capability m echanical data cases: to-220 molded plastic epoxy: ul 94v-0 rate flame retardant terminals: leads solderable per mil-std- 202, method 208 guaranteed polarity: as marked high temperature sol dering guaranteed: 260 /10 seconds .16?,(4.06mm) from case. weight: 2.24 grams to-220 dimensions in inches and (millimeters) m aximum ratings and electrical characteristics rating at 25 ambient temperature unless otherwise specified. single phase, half wave, 60 hz , resistive or inductive load. for capacitive load, derate current by 20% type number symbol gp 1001 gp 1002 gp 1003 gp 1004 gp 1005 gp 1006 gp 1007 uni ts maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward rectified current .375?(9.5mm) lead length @t c = 100 i (av) 10.0 a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method ) i fsm 125 a maximum instantaneous forward voltage @5.0a v f 1.1 v maximum dc reverse current @ t c =25 at rated dc blocking voltage i r 5.0 ua typical junction capacitance ( note 1) cj 30 pf typical thermal resistance (note 2) r jc 3.0 /w operating and storage temperature range t j ,t stg - 65 to + 150 notes: 1. measured at 1 mhz and ap plied reverse voltage of 4.0 volts d.c. 2. thermal resistance from junction to case mounted on heatsink size 2? x 3? x 0.25 ? al-plate
- 551 - fig.2- maximum non-repetitive forward surge current peak for ward surge current . (a) 1 2 5 10 20 100 50 25 0 50 75 125 100 150 175 number of cycles at 60hz 8.3ms single half sine wave jedec method fig.3- typical instantaneous forward characteristics per leg instantaneous for ward current . (a) 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0.1 0.4 0.2 1 4 2 10 20 40 100 200 400 forward voltage. (v) fig.4- typical reverse characteristics per leg instantaneous reverse current .( a) 0 20 40 60 80 100 120 140 0.1 0.4 0.2 1 4 40 2 10 100 percent of rated peak reverse voltage. (%) tj=25 c 0 tj=125 c 0 fig.5- typical junction capacitance junction cap acitance.(pf) 0.1 0.5 1 4 10 40 100 1000 400 20 0 40 60 100 80 120 reverse voltage. (v) tj=25 c 0 f=10 mhz vsig 50mvp-p fig.1- maximum forward current derating curve average for ward current . (a) 0 50 100 150 2 4 6 8 10 12 case temperature. ( c) o single phase half wave 60hz resistive of inductive load ratings and characteristic curves (GP1001 thr gp1007) u tj=25 c pulse width=300 s 1% duty cycle o
|
